Search results for "flow [Keywords]"
showing 10 items of 469 documents
Speed Stochastic Processes and Freeway Reliability Estimation: Evidence from the A22 Freeway, Italy
2013
In this paper, a criterion for predicting the reliability of freeway traffic flow is presented. The idea is based on an analysis of spot speed time series divided into sequences of events of random and homogeneous traffic processes. For each process, the flow rate and density were calculated; then the relationships between parameters of spot speed processes and vehicular density were obtained. Using these relationships and a simulation procedure for the spot speed process, a formulation for predicting the reliability of traffic flow moving along the offside lane on the freeway roadway was derived. Through this formulation and the measurements of flow rate and speed, the probability of insta…
Once t hrough m ultistage fl ash d esalination: gPROMS d ynamic and s teady s tate m odeling
2010
This study focuses on modeling the steady state and dynamic behavior of the multistage flash desalination process (MSF) using gPROMS. This modeling tool allows for simultaneous coding of the system dynamics and steady state performance. In addition, it allows the use of the most efficient solvers for a set of non-linear differential and algebraic equations describing the MSF process. The system model and analysis are based on actual plant data that includes 21 flashing stages and a capacity of 378 kg/s (32,000 m3/d). The simulated unit is part of a massive MSF installation in Doha, Kuwait. System's dynamic behavior is simulated by a step change in the input values of the main operating para…
New Expression of the Hydraulic Jump Roller Length
2012
AbstractThis paper presents the results of an experimental investigation on the roller length of both classical and B-jumps on smooth beds. Using the measurements conducted in this investigation and those available in the literature, a new relationship is proposed for estimating the roller length of classical and B-jumps on smooth beds. Finally, it is demonstrated that the proposed equation is also applicable to estimate the roller length of hydraulic jumps on rough horizontal beds.
Power quality effects on the measurement of reactive power in three-phase power systems in the light of the IEEE Standard 1459–2000.
2007
Reactive power is a very important quantity in electric power systems since it affects the efficiency of these systems. Also, capacitive loads can produce over-voltages in electric transformers by Ferranti effect, which produces bad power quality, so it is necessary to measure the reactive power correctly. In this paper reactive phenomena in three-phase power systems with unbalanced voltages are expressed and measured in the light of the IEEE Std 1459-2000. For analyzing the reactive phenomena the positive-sequence fundamental frequency instantaneous reactive power is used. By comparing the expressions of this instantaneous power in three-phase systems with unbalanced voltages with those co…
Numerical Analysis of Medium Scale PV Plants and Their Power-Flow Control System With a Simple Three Phase Inverter
2012
This paper presents a mathematical analysis of a medium scale Photovoltaic (PV) power generation system connected to the distribution network and of its control system, in which the conversion stage is unique thanks to the absence of a boost chopper. Boost choppers are usually used as actuator for maximum power point tracking (MPPT). The conducted analysis leads to the conclusion that the used inverter presents two degrees of freedom that can be easily exploited in a control system in which the inverter simultaneously realizes the interconnection to the grid and at the same time realizes the MPPT control. The structure of the control system is then presented, discussed and then validated by…
Uncertainty evaluation of a Backward/Forward Load Flow algorithm for a MV smart grid
2015
This paper presents the uncertainty evaluation of an innovative measurement algorithm for load flow analysis in MV distribution networks. The measurement procedure is based on Low Voltage (LV) load power measurements applied on a Backward/Forward (B/F) algorithm for the Load Flow (LF) resolution. Furthermore, in the procedure a three phase voltage measurement at the MV generating substation bus-bars is also considered. The accuracy analysis of the LF algorithm is performed in the case of a real load condition in the distribution grid of Ustica island, Italy. The analysis takes into account the uncertainty of the measurement instruments at the LV side of each secondary substation power trans…
A novel fuel cell-based power system modeling approach
2013
Nowadays, fuel cells are the most promising source of energy for stationary applications. Unfortunately, the power density of fuel cells is not adequate for modern applications. A fuel cell - based hybrid power supply is required. The fuel cell is coupled with a high-energy density power source to improve performances of the composite power source. A power management stage is introduced between the two basic sources to control the power flow path from the fuel cell to the auxiliary source and the load. In order to avoid effects of a limited power density of the fuel cell on the whole power supply, sophisticated power management algorithms are implemented. Accurate modeling is required to te…
Bubble formation at variously inclined nozzles
2014
Bubble formation at variously inclined submerged nozzles, fed with a continuous gas flow rate, is investigated. Results confirm previous findings, such as a substantial independence of bubble size of nozzle diameter and its dependence on the cubic root of gas flow rate at sufficiently high values of this parameter. Nozzle inclination in the range between 0 and 135° from the vertical upward orientation is found to have a negligible effect on bubble size. Observed bubble rise velocities lead to an estimation of the average liquid velocity induced by bubbles motion, leading in turn to a very simple correlation for the estimation of the liquid velocities induced by the repeated passage of bubbl…
Mathematical and numerical modeling of an airlift perfusion bioreactor for tissue engineering applications
2022
The Tissue Engineering (TE) strategy is widely focused on the development of perfusion bioreactors to promote the production of three-dimensional (3D) functional tissues. To optimize tissue production, it is worth investigating the engineering parameters of a bioreactor system for identifying a beneficial range of operation variables. Mathematical and numerical modeling of a perfusion bioreactor is capable to provide relevant insights into the fluid flow and nutrients transport while predicting experimental data and exploring the impact of changing operating parameters, such as fluid velocities. In this work, the hydrodynamic parameters and oxygen transport were investigated using mathemati…
Performance evaluation of a biotrickling filter treating a mixture of oxygenated VOCs during intermittent loading
2008
Laboratory scale-studies on the biodegradation of a 1:1:1 weight mixture of three oxygenated volatile organic compounds (VOCs), ethanol, ethyl acetate, and methyl-ethyl ketone (MEK) in a biotrickling filter (BTF) were carried out using two identically sized columns, filled with different polypropylene rings. The performance of the BTFs was examined for a period of 10 months applying several operational strategies. Similar performance was obtained for both supports. Intermittent flow rate of trickling liquid was shown beneficial to improve the removal efficiency (RE). Continuous feeding of VOC resulted in an excessive accumulation of biomass so high pressure drop was developed in less than 2…